Unplug the coolant temp sensor out of the center of the factory head. Remove the spark plug wires and remove the spark plugs from the head. Remove the rear coolant hose and the smaller coolant hose near the oil tank.A Mity-Vac style suction drain works great to remove coolant without spilling Be sure to use a few drain pans under the sled to catch the pilling coolant. Drain the coolant by removing one of the lower coolant hoses from the motor.Unless noted, trademarks are the property of Polaris Industries Inc. YouTube® is a registered trademark of Google Inc. To find diagrams and replacement part numbers, use the online parts catalog. Maintenance tips, procedures and specifications can be found in your Owner's Manual. Find a dealer near you with the Dealer Locator. Confirm the reset by tapping the red RESET button.įor more information, see your authorized Polaris Dealer. To reset the interval on a seven-button RIDE COMMAND display:ĥ. Programmable Service Interval on Seven-Button RIDE COMMAND Display Press MODE to save and exit the settings menu. Press MODE to reset the existing value and exit or press either toggle button to change the value. Press either toggle button (5) to cycle to the "Service Hours" option. Press and hold the MODE (4) button to enter the settings menu.Ģ. Refer to the recommended oil change intervals.ġ. When this feature is enabled, it provides a convenient reminder to perform routine maintenance. The wrench icon will flash for about 10 seconds when the counter reaches zero and each time the key is turned on thereafter until the counter is reset. As hours of engine operation increase, the counter decreases. The service interval counter on the instrument cluster of your RZR is programmed to 25 hours at the factory. Dispose of used oil, filter and rags properly. Reinstall the cargo box access panel, engine service panel and seats.Ģ0. When finished, reinstall the dipstick and lock the lever.ġ9. If the oil level is over the upper mark, change the oil immediately.ġ8. A rising oil level between checks during cold weather operation can indicate contaminants such as gas or moisture collecting in the crankcase. Add the recommended oil as necessary to bring the oil level within the SAFE range (between the holes) on the dipstick. Remove the dipstick and check the oil level.ġ7. Make certain the dipstick is inserted all the way down to ensure an accurate reading.ġ6. Remove the dipstick and wipe it dry with a clean rag.ġ5. Wait at least 15 seconds before removing the oil dipstick.ġ4. Start the engine and allow it to idle for 30 seconds.ġ3. Each oil change kit comes with 3 quarts (2.8 liters) of oil.ġ2. The oil capacity of a RZR XP Turbo is 2.75 quarts (2.6 liters). Fill the engine to the recommended specification. Add engine oil through the oil fill cap (2) located on top of the engine valve cover.ġ1. Torque the drain plug to 12 ft-lbs (16 Nm).ġ0. Reinstall the engine crankcase drain plug with the 6mm Allen socket. Inspect the sealing washer on the drain plug for burrs or nicks. It is included in both oil change kits.Ĩ. Turn by hand until the filter O-ring contacts the sealing surface and then turn an additional 3/4 of a turn. Check to make sure the O-ring is in good condition.
Lubricate the O-ring on the new oil filter with a film of clean engine oil. This may spread oil into surfaces that may get hot, which may lead to a fire.ħ. Do not use a hose/pressure washer to clean up spilled oil on a vehicle. Clean the filter sealing surface on the engine crankcase with a clean rag and ensure the original oil filter O-ring is not stuck to the crankcase. Tip the open end of the oil filter up to minimize oil spill.Ħ.
Using the oil filter wrench, turn the oil filter counter-clockwise to remove it.
Place shop rags under the filter to catch any oil spilled during removal. The engine should be off for at least 2 minutes prior to removing the oil filter.ĥ. Access the oil filter through the driver's side rear wheel well. Place a drain pan under the engine crankcase and remove the drain plug (1), using a 6mm Allen socket.Ĥ. Allow the engine to cool down before draining the oil.ģ. The Extreme Duty Oil Change Kit is part number 2881697.ġ. The PS-4 Oil Change Kit is part number 2881696. Always wear safety glasses and nitrile gloves when changing your oil and filter. To learn more about tools, read the Tools and Fasteners Guide.Īlways change the oil and filter at the intervals outlined in the Periodic Maintenance Chart found in your Owner's Manual.
0 kommentar(er)
